People waste so much money by going to a mechanic just to repair or replace some ordinary car parts. In this way, without throwing money in the water, you can change some parts of the car by sitting at home with some ingenuity. If the car is more expensive then maybe the cost of replacing the parts is also higher. With just a few hours of work, you can halve this cost. If you have a minimal initial idea about the equipment, then you can easily repair car parts. And when you do these yourself, you can use some eco-friendly ingredients. You can reduce the cost of repairing your car parts by filling the car’s fuel tank and moving around comfortably with the car. Let’s see how you can repair your car parts at home.
1. Changing Fuel Filter
Fuel filters should be changed every few days. Occasionally if you change the fuel filter the mileage of the car can be increased up to 10,000 miles. A dirty fuel filter greatly reduces the efficiency of your car. So even if it is for the maintenance of the fuel filter, it should be changed every few days. The steps to change the fuel filter are very simple. First, open the battery and de-fuel the fuel line. Then remove the fuel line from the filter. Then replace WASA, attach new filters. Check everything again. Finally, start the car engine and see if there is any leakage. Look around to see if there are any ways to make the old filter new. This is because the removal of old filters can cause environmental pollution. Keep an eye on those old filters.
2. Changing brake pads
Changing the brake pads regularly is much more important for a car. As the brake pads become more worn out, the cost of replacing them increases. And also causes a lot of damage to other parts. Brake pads relate not only to your life but also to the lives of the people around you. To replace the brake pad you will need a car jack, a lug nut wrench, socket set, C clamp. And these you can find in any hardware store. At the end of the shift, dispose of your old brake pad in a place where there is no risk of harm to the environment or human beings.
3. Replacing Spark Plug
Another part of keeping your car moving and alive is the spark plug. It is very important to take care of and replace the spark plugs regularly. As time goes on, the coating of metal on the electrode turns into carbon. This makes it difficult for the plug to spark when mixed with fuel/air and destroys the efficiency of the whole vehicle. According to several experts, some special plugs, as the price suggests, increase power or reduce fuel consumption; Doesn’t actually do anything like that.
Some plugs reduce fuel consumption such as E-Three or Halo plugs. When the cost goes down, the plug is the original plug that came with the car. Replacing the spark plug is a very easy task. First, unplug the fuel wires from the old spark plug. Then remove the plugs with a socket wrench. Attach the new plug and apply a coating to the fuel cable covers with dielectric grease. This will protect the wires inside the coating and will not spread around. Became the replacement of the spark plug.
4. Windshield Repair
It is not always right to think that the windshield can be repaired in the garage. You can repair the windshield yourself at home very easily and efficiently. The first thing you need to do to repair the windshield is; You have to buy a windshield kit from any shop or garage. First, clean the damaged area up to 12 inches with a glass cleaner. Then smooth the place with a blade. Remove the glass pieces inside the chip. Most kit boxes have a device for injecting adhesive into the windshield. Finally, do the rest of the work on the windshield. Remember, if you want to get the job done quickly and accurately, you should never do it in the heat of the sun. This is because the sticky substance is likely to harden in sunlight.
5. Power Steering Flush
The power steering flash looks a lot like a medicine drug drop. It is used to get old oils out of the steering wheel. Also used to give new oil. And using a device that looks like this drop, you can remove 90 percent of the old/dirty oil. As much oil as possible should be extracted from the tiny space next to the engine compartment. Take out the oils and keep them in a plastic container so that you can discard them later. Then fill with new oil. Start the car and check the steering wheel back and forth to check. Turn off the start by pressing the ignition switch again. Repeat the whole process. Turn on and off three or four times in the same way until the fluid is completely clear.
6. Transmission Fluid Replacement
Fluid replacement of the transmission in a mechanic’s shop is called transmission flush. In this method, clean oil is inserted inside the automatic transmission. The main task of this method is to push the old and dirty oils out of the system. According to some mechanics again this method is not correct. They think it could cause transmission problems. The method of fluid replacement of the previous transmission was more efficient and easier and much more expensive. It will take the same jack and a few jacks stand to lift your car upwards. Through which lift the car up and remove the pan bolt from the bottom of the car. Use a large plastic lid container and discard the dirt. So that the oils can be easily taken to any place for cleaning later. Be sure to replace the fluid filter when cleaning the inside of the transmission pan. Do not tighten the bolts too tightly when re-installing the pan as it may leak.
These were our today’s tips and tricks. Keep an eye on Prohori’s website or Prohori’s Facebook page to get more new and exciting information about the car.
